Feb 12, 2015 even if you don't have the alarm.com 'home automation package', you can configure it to run locally at panel itself (set Q79 to 2 for local home automation Rules and Scenes). If your Vivint/other panel is locked out (Q44), you will not have access to system configuration, and you will have to get your panel unlocked, by disabling lockouts.
Touch screen wireless keypad, Install instructions, Before you begin
.Alarm history with system event log: Each alarm and system alert is logged into the system’s memory. These events can be displayed and reviewed at the Control Panel or remotely by the Central Station.Real time clock and calendar shows on the system’s display and is used to time stamp. Control Panel The majority of GHS alarm systems include a 24-hour backup battery; this means that the alarm system will still operate if the power goes out. Follow below steps to replace the main battery in a GHS 2GIG home alarm system. Page 2: User Guide.
Advertising
- The product manuals (or other materials) provided here are those of third parties, not Protection 1, and Protection 1 makes no representation or warranty as to the accuracy or completeness of the product manuals or the data contained therein.
- 2GIG Panel Manuals 2GIG User Manual. Floyd Total Security 9036 Grand Ave S, Bloomington, MN 55420. P: 952-881-5625 e: info@floydtotalsecurity.
INSTALL INSTRUCTIONS
This document describes the basic installation information for the 2GIG‐
2GIG‐TS1 and the steps necessary to “pair” (or learn in) the Touchscreen
Wireless Keypad to the Control Panel.
2GIG‐TS1 and the steps necessary to “pair” (or learn in) the Touchscreen
Wireless Keypad to the Control Panel.
Box Contents
•
2GIG‐TS1
•
AC Power Supply
•
AC Power Supply Bracket
•
Screws and anchors
TIP:
The box contents will vary depending on whether the 2GIG‐TS1
was purchased as part of a kit or not.
BEFORE YOU BEGIN
Is the 900 MHz Transceiver installed in the Panel?
For the 2GIG‐TS1 to communicate with the Control Panel, the 900 MHz
Transceiver (2GIG‐XCVR2) must be already be installed in the Control
Panel.
Transceiver (2GIG‐XCVR2) must be already be installed in the Control
Panel.
Is the 2GIG-TS1 paired with the Control Panel?
The 2GIG‐TS1 and the Control Panel have to be paired to communicate
with each other.
with each other.
To check for to see if the 2GIG-TS1 is paired with the
Control Panel
Control Panel
Upon power up, the 2GIG‐TS1 displays the following screen:
2GIG-TS1 PRODUCT OVERVIEW
The Model 2GIG‐2GIG‐TS1 Touch Screen Wireless Keypad is a remote
control device that offers the functionality of a system keypad but also
extends all user control of the 2GIG Control panel to other locations in a
user’s home. Using the 2GIG‐TS1, users can control lights, thermostat
and door locks and see the status of every zone in their home using the
exact same and familiar interface found on the Control Panel. The keypad
is designed for indoor use only.
control device that offers the functionality of a system keypad but also
extends all user control of the 2GIG Control panel to other locations in a
user’s home. Using the 2GIG‐TS1, users can control lights, thermostat
and door locks and see the status of every zone in their home using the
exact same and familiar interface found on the Control Panel. The keypad
is designed for indoor use only.
IMPORTANT:
Not for UL 985 installations.
The panel
and
buttons serve as controls as well as indicators.
Pressing the
(Emergency) button displays emergency icons on the
display for Panic, Fire, and Emergency alarm activation (each has
programmable options and can be enabled or disabled). Pressing the
programmable options and can be enabled or disabled). Pressing the
2 Gig Alarm System
(Home) button changes the system display to the Home Screen. The
keypad is powered from a plug‐in power supply. The 2GIG‐TS1 exchanges
information through a secure 2‐way wireless connection with the Control
Panel.
NOTE:
keypad is powered from a plug‐in power supply. The 2GIG‐TS1 exchanges
information through a secure 2‐way wireless connection with the Control
Panel.
NOTE:
Before using the 2GIG‐TS1 it must be “learned” into the
2gig Go Control User Manual
Control Panel.
Mounting Tools
Some special tools may be required to mount the 2GIG‐TS1 onto the
wall:
•
wall:
•
Screwdriver
•
Pencil
•
Wire stripper
•
Staple gun
•
Drywall saw (or equivalent)
•
Ladder
PREPARING THE KEYPAD
NOTE:
Check that the 2GIG‐TS1 Keypad is functioning before
selecting a location for the Keypad.
1 Remove the screw.
2 Flip open the back cover of the 2GIG-TS1.
3 Disconnect the hanging strap.
4 Use the back cover as the mounting plate.
2 Flip open the back cover of the 2GIG-TS1.
3 Disconnect the hanging strap.
4 Use the back cover as the mounting plate.
2GI
Touch Screen Wireless Keypad
For Remote Control of the 2GIG Security System
Advertising
Popular Brands
Popular manuals